Description
RMA has upgraded its popular Level 3+ body armor plate to create an all new Generation 2 version. Generation 2 defeats multiple M855A1 rounds with ease, yet remains lightweight and affordable. Plus, it has a thinner profile than Generation 1. Not only is it multi-hit rated to defeat the M855A1 round, but it’s also been tested to the upcoming NIJ .07 RF2 standard. This is without a doubt, the new standard in the Level III+ body armor protection. But what else would you expect from RMA?
RMA’s Level 3+ body armor plates (models #1091-1094 Gen2) have a ceramic body armor strikeface and Dyneema® UHMWPE build. We specifically tested Generation 2 to meet the new NIJ 0101.07 standards set forth by the National Institute of Justice. With RMA’s Level III+ plates, there’s no confusion to what Level III+ (RF2) ceramic body armor should be. After all, the standard for Level III+ plates (RF2) is the ability to defeat the M855 green tip, XM193, 7.62×39 MSC and the M80 Steel Jacketed NATO round. This body armor plate does that with flying colors. But we’ve taken it further with its ability to defeat the M855A1.
If you’re looking for a lightweight ceramic body armor plate that is affordable in price, yet sets the standards in ballistic performance, this plate is for you.
What is RF2 (Level III+)?
The upcoming standard set forth from the National Institute of Justice (NIJ) will implement a new ballistic rating system for hard and soft armor. When the new standards for armor are officially released, RF1 (Level III), RF2 (Level III+) and RF3 (Level IV) will be the hard armor names to replace the current ratings of Level III, Level IV, etc. (Level III+ was never an official compliance standard, previously).
But the differences in the ratings go far beyond the nomenclature. Under the current level III standard, a plate must defeat 6 rounds of M80 Steel while also boasting a back face deformation of less than 44mm. Because of that, many companies would rate their armor plates as Level III+ simply because it defeated what they personally deemed was a more threatening round than a M80 NATO Steel projectile. Many companies would say their plate could defeat a single round of M193, 7.62×39 MSC or M855 green tip and boast that their plate was a Level III+ or Level III++ despite the fact that their plates haven’t even been tested to defeat six (6) M80 NATO projectiles – the level III minimum requirement.
NIJ 0101.07 Draft Standard for RF2
However, under the new standard, RF1 plates (previously Level III) must now defeat three (3) M80 NATO Steel rounds, three (3) 7.62 x 39 MSC AND three (3) M193 BT to earn its rating. If a plate cannot defeat those rounds while also boasting a BFD of less than 44mm, they will not even be considered for the RF2 rating (previously Level III+). So you MUST pass RF1 to have a chance to become an RF2 plate. Once the plate passes the RF1 testing, more plates must be submitted for further testing, which will also include defeating three (3) rounds of M855 green tip as well.
At RMA, we have created this next generation plate that has not only passed RF1 and RF2 testing, but additionally defeats the M855A1 round. Here is the official RF1 and RF2 testing report for this plate. Going forward, a company will have to prove that they can defeat all of those rounds. And RMA is the first company to do so.
| RF1 must defeat: | Three (3) M80 NATO Steel (149 grain) | 2780 ft/s |
| Three (3) 7.62x39mm MSC | 2380 ft/s | |
| Three (3) 5.56mm M193 (56 grain) | 3250 ft/s | |
| RF2 must defeat (All of the Above, PLUS): | Three (3) 5.56mm M855 Green Tip (62 grain) | 3115 ft/s |
| RF3 must defeat: | One (1) to Three (3) 7.62×63 M2AP | 2880 ft/s |
Level 3+ Body Armor Plate Carrier Compatibility
RMA’s multi-curve Level III+ body armor plates pair perfectly with the Crye JPC 2.0. If the size medium body armor plate is the right for you, you’ll want to pair it with the medium JPC 2.0. If you need a large armor plate, then the size large JPC 2.0 will be what you’re looking for. However, if the Crye JPC 1.0 is the plate carrier you’d like to pair with these Level III+ armor plates, then we suggest a carrier that is one size larger than the plate. For example, a medium III+ body armor plate pairs well with the JPC 1.0 size large. RMA’s Level III+ body armor plates are also compatible with the Shellback SF plate carrier. You’ll want to pair the size of the SF carrier to the size of the body armor plate.
You can also size these plate to fit with the 0331 Tactical Tailwind plate carrier. The 0331 Tactical Sierra plate carrier is ideal as well. Size medium and large plates fit into the M/L size carrier. Plus, 11X14/XL plates fit into the L/XL plate carrier with ease.
Level 3+ Body Armor Specs
RMA Level 3+ Ballistic Lab Report
Which Armor Is Right For Me?
Details:
- Stand-Alone Level 3 Plus Body Armor
- Full Edge-to-Edge Protection
- 8.75″ W x 11.75″ H – 4.9 lbs. (Size Small)
- 9.5″ W x 12.5″ H – 5.6 lbs. (Size Medium)
- 10.25″ W x 13.25″ H – 6.4 lbs. (Size Large)
- 11.00″ W x 14.00″ H – 7.0 lbs. (Size XL)
- Warranty: 5 Year Manufacturer’s Warranty
- Armor Shape: Multi-Curve
- Armor Cut: SAPI/ESAPI-Cut
- Thickness: 1″ (+/- .125″ tolerance)
- Armor Build: Ceramic & Dyneema® UHMWPE
- 600 Denier Water Resistant Cover
- NIJ 0101.07 RF2 Tested
- Free Incident Replacement (If our armor saved your life, please let us know!)
- Made in Centerville, IA – USA
- RMA Return Policy
- RMA Hard Armor Warranty Policy
PLEASE NOTE THAT BY PLACING AN ORDER YOU AGREE TO COMPLY WITH ALL LOCAL, STATE, AND FEDERAL LAWS REGARDING BODY ARMOR.
18 U.S. Code § 931. United States law restricts possession of body armor for felons convicted of a crime of violence (as defined in 18 U.S. Code § 16). Many U.S. states also have penalties for possession or use of body armor by felons. By purchasing body armor from RMA Armamant, Inc. or employees of RMA Armament, Inc., you are certifying that you have not been convicted of any crime that would restrict you from being able to purchase or possess body armor under any Federal or State laws.
***DUE TO THE LIFE-SAVING NATURE OF THIS PRODUCT, ALL SALES ARE FINAL***
Scott C. (verified owner) –
Light weight
Alex (verified owner) –
Light and comfortable. The multiple curves fit well.
Tyler (verified owner) –
I would highly recommend. Exactly as described with quick delivery
James F. (verified owner) –
These plates boast the same rating and material as the plates I used in the army. The internal material feels well constructed and reliable as you’d expect. It is very light weight for its protection rating (a couple ounces lighter than my military plates) and ships very well protected. Upon inspection out of the box the plates have no damage the the edges and passed the twist test. There are two reasons I cannot give 5 stars. First reason in the water proof rating. I would perfer a plate more resistant to water but these will do. I work in a rainy environment and do a small amount of water training. I’d like ky armor to withstand moisture in the long run. 2nd reason is the external material. It is soft which is nice but it is also very warm and stretchy. In the summer these plates get very very hot to wear. In the winter they are great. So it’s a trade off. The stretchy part makes things difficult though. When inserting this plate into a carrier that is a little on the snug side this material stretches and shifts A LOT. Once the late is fully inserted the material is under a lot of tension at the top of the plate woth how much it is being stretched. I am not very confident in the long term durability of this external material. Overall I trust this plate will save my life when it matters but there are smaller details I believe matter and are being overlooked. My reccomendation in the future would be to utilize a harder wrap like Cordura or a similar fabric that can be paired with other compounds to create a cooler, slightly thinner, more water resistant, and easier to insert into the carrier plate. I will buy this product again though and I think RMA has outdone themselves with this plate considering it almost matches my $1600 plate set issued by the army.
Adam M. (verified owner) –
Plates are light seem to be well constructed. They fit perfectly in my crye jpc 2.0. The only knock I’ll give is one of the plates has asymmetry to the top curve which is very noticeable.
Daniel (verified owner) –
This plate came well-packaged and is clearly of a quality build. It’s drop-cushioned and easily worn, both from a fitment/comfort and a weight perspective. Well done, RMA.
Elycres (verified owner) –
Love it. Definitely recommended
Anonymous (verified owner) –
Personally I am very pleased with the armor! Either, everyone complains about their armor a lot, or I have an awesome set up with my lovely T REX ARMS AC1, because these plates are lightweight and very comfortable. Instead of dreading wearing it I look forward to it. They were very tight going into the plate bag but but there is no wiggle or slop. Would highly recommend.
Kevin K. (verified owner) –
the armor is versatile comfortable and fits perfectly in my CRYE JPC. 2.0. its great!
Hunter (verified owner) –
Great plate so far. Run my plates in a Qore Essentials carrier and they work great. The weight is a perfect balance between coverage and comfort and the price is one of if not the best bang for buck plate. Moral of the story, it’s a great plate for a good price.
Bryan S. (verified owner) –
Very well made. No loose threads or fabric. Fit perfectly in my Agilite K Zero plate carrier
jake hruska (verified owner) –
awesome product at a good price zero complaints from me
Sang (verified owner) –
Great product
Keith (verified owner) –
Good stuff, fits well. Paired with a whiskey two for plate carrier 24 you can barely tell you’re wearing plates
JASON G. (verified owner) –
Very happy with the purchase so far. I have a set of 3 Plus coated steel from another company and I really like the fit and feel of these over the steel.
Due to my frame 5’9″ fairly muscular 195lbs. I am right between the Med and Large plate recommend sizes, so due to stock availability I opted for the Large. I am not upset but I would prob prefer the Med just to gain that slightly smaller profile. These do not hinder my mobility I just think the medium would still give me great coverage along with the reduced footprint might be more optimal. For someone built like me it is really a personal preference of extra coverage or not. But since the plates are not exchangeable that is not an option. Overall I would definitely recommend this product. And I hope this helps anyone that falls into that in-between category with their purchase.
Verified Buyer (verified owner) –
Arrived fast and well packed/protected. Plate finish was high quality and clean. These plates are slightly thicker than others of same rating but at this price and quality I don’t mind, just keep that in mind when pairing with a plate carrier. VERY snug fit in a FCPC V5, but they did fit. Multi-curve is a must for extended wear and I can’t recommend it enough.
Verified Buyer (verified owner) –
Great buy! Bought the 13.25 x 10.50 for the Large Crye Precision JPC 2.0. Fits perfectly. No need to look any further if you have CP gear. Worth the money.
Philip (verified owner) –
Thankfully never had to test it…for obvious reasons lol. But got this and a Level 4…non “slim” version. Seems good quality and like any insurance, I hope I never need to use it for real.
rigel s. (verified owner) –
fast shipping and Excellent product from RMA. Would buy again in some time
Jonathan M. (verified owner) –
My knees hurt but this plate is comfortable. A new hole would hurt a lot more.
Kristopher (verified owner) –
Fast shipping, honors the military, what else is there to say until I take one in the plate!
Benjamin H. (verified owner) –
Customer service and shipping were very good. Product description and sizing were spot on. Armor strikes a good balance of protection, weight, and price.
Derek T. (verified owner) –
Purchased a pair of 1092 rf2 multi-curve plates. Lightweight, comfortable and fit perfectly in my ferro slickster. Best pair of plates I have owned so far and buffman range on YouTube has great reviews of these plates stopping multiple rounds of .308 and m855a1
Anonymous (verified owner) –
The specifications were as stated, except the dimensions – the width and height were around .3” bigger than stated, which created a problem – my large sized plate carrier could not fit the plates, had to change carrier size L to size XL.
James (verified owner) –
Great fit in my Crye job 2.0.
Anonymous (verified owner) –
Great plate and fit in my JPC 2.0 just fine. Medium plate with medium JPC. Not NIJ certified but supposedly it will be once the official NIJ specs drop. Also arrived fast and securely boxed.
Anonymous (verified owner) –
I’m happy with the products
Anonymous (verified owner) –
Bought these to replace my hesco l210’s, and even though they list them as heavier, they feel alot lighter and carry easier. I would definitely recommend these to anybody looking for plates
Derek Olson (verified owner) –
Excellent armor at a great price point. I am happy to support a business with great products and great 2A values.
Anonymous (verified owner) –
It’s made in the U.S.A., first quality, light weight in this model. Perfect.
Anonymous (verified owner) –
The curvature of this plate feels odd but it fits well. I am used to soft body armor so this took some getting used to. No complaints yet. Wear it 6 days a week for work and it does exactly what it’s supposed to do.
Abraham (verified owner) –
This is my second RMA purchase. I am highly satisfied with both purchases. The website is set up very well so that the buyer can assess the comparable data in making a decision. I went with the slightly heavier III+ instead of III; and all of that info reference weight and cost was easily comparable. NIJ comparison images are also helpful.
Michael Grimes (verified owner) –
If you’re in the market for this armor as well as buying a Spiritus Systems plate carrier I would size up. For example the Spiritus Systems medium should have fit but I had to go with a large. I’m 5’11 190 pounds of beefcake for perspective. Not a problem of the plate carrier or the armor, just know that was my experience.
Anonymous (verified owner) –
Thankfully haven’t had to test the plate’s capabilities yet, and hopefully I never have to. That said, I have no doubt it will do the job if needed. It is very comfortable in the carrier, and from everything I’ve seen you can’t beat the cost for the amount of protection and how lightweight it is. My only complaint is that they are always out of stock. I doubt I speak for myself only when I say, crank up the medium production please!
Matthew (verified owner) –
Got these for a slim carrier, to stay light and have practical security. I’ve worn them 3 times in classes so far, they really aren’t too heavy which is what I like the best. Haven’t gotten shot with them on yet, but I trust the brand and testing. Definitely recommend these to my family and friends.
Voya V. (verified owner) –
Very impressed with this body armor and company as a whole. It is my first RMA purchase and certainly not my last. I bought the 1092 plates in medium, which always seem to be out of stock. I wanted them because I wanted to run them in a Crye JPC 2.0. I call RMA and they said they just got in some fresh inventory and update their website later that day. An hour later the inventory number jumped to 20, so I bought 2 instantly.
They arrived a few days later and the manufacturing date on the tag was just 5 days earlier! The fit is tight but perfect. I took my time, spending 3-4 min installing each plate carefully and evenly. The end rig is nice perfectly tight at all corners/edges. The 1092 plates weight 4.5lbs each with nice foam around them. I was impressed with the overall fit and finish of the plates. Very high quality. The shape and foam form a super comfortable fit. 9lbs of plates, and 1lb of plate carrier makes for a ridiculously comfortable 10lb rig that I can wear all day, and forget that I’m even wearing it.
I require to trail blaze roughly 15miles a day in the North GA mountains. Sometimes up to 20miles with 3.5miles of elevation change. That’s no trails, carrying an Eberlestock FAC Track 7lb bag, a light 25lbs of gear/food/water inside, 8lb loaded FA M4A1 with 4lbs (4XMags) in a mag holder strapped to the 10lb plate carrier with RMA 1092 medium plates. Wearing Crye Combat Pants and Shirt with Rocky S2V boots and a standard Glock 17 sidearm with two extra mags in an Eberlestock fanny pack. That is about 50lbs total, up from 40.
I did a 10mile trial run two weeks ago to test the 25% increase in weight with the body armor, and it did not have as much of an impact as I expected. The 9lb plates from RMA are as light as Class III plus gets, plus the foam and shape make them silly comfortable. They wear so nicely in the JPC 2.0 that it feels less than the 10lbs they weigh. I showed off my Rig to colleagues today and they all want the same set up after trying it on. But of coarse the 1092 plates in medium are out of stock due to demand. Come on RMA, do batches of 50+ to meet demand. You make too good of a product to order in small batches. Everybody and their mom wants the 1092. When I was the first to buy 2 of the 20 that popped up that day, I felt privilaged that I got them. I think they should be more available to customers. Demand certainly exceeds supply.
That all being said, I highly… highly… recommend RMA and this particular Level 3+ plate. I don’t think there is anything better than the 1092 plates in a Crye JPC 2.0 carrier. No need to look further. And if you’re on the website and see the 1092’s available, instantly add 2 to your cart. If the wife says dinner is ready, tell her to wait while you check out. It’s that important. Last thing you want to happen is you finish dinner and all the 1092s are gone. Then you’ll missout on sleep for weeks, thinking about what could of been, had you of ordered 1092s instead of hearing what little Jimmy learned in school that day while eating chicken and mashed potato’s. I see I’m blabbering now, but let me just cut to the chase: A+ product, A+ company, A+ customer service, order the elusive 1092 if you see them.
Benjamin (verified owner) –
Very comfortable
Adam (verified owner) –
I wouldn’t shop anywhere else for body armor. Great Products and great service! The most important but hardest to find in a company lately. And yes… MADE IN THE USA!
Andrew P. (verified owner) –
Very happy with my armor! Very light weight and the multi curve fit is great. Stops all common rifle caliber and won’t break the bank
Chase B. (verified owner) –
The only armor I could find that was NIJ tested and certified, lightweight, AND affordable. What an amazing company. Plates are also comfortable and fit extremely well. If you’re debating on whether to buy RMA or not, just do it.
Anonymous (verified owner) –
The 1094 plates are comfortable and light for their size. Will probably be buying another set in the future.
Chris W. (verified owner) –
These plates went above and beyond my initial thoughts. The multi curve feels great, they’re insanely light, and you can’t beat the price. I’m running the velocity systems scarab in medium with the medium plates, they said the plates may not fit because of thickness, but they fit with a little persuasion. When I’m in the market for some level 4’s I’ll definitely be getting from RMA
Andrew A. (verified owner) –
I haven’t been shot yet so I don’t know how well it works but it’s lightweight and very comfortable.
James Stone (verified owner) –
Stops M855, M193 at 3400+ fps and M80 ball. Comfortable enough to wear all day. Just don’t take it up against armor piercing rounds or M855A1 and you should be good to go!
Jose (verified owner) –
I own 2 sets of these plates, single and multi curve. The multi curve are definitely more comfortable and worth the price. I will be getting more soon. Maybe the level 4 if and when the price comes down a little.
Awesome plates, worth the wait.
Also the shipping was ridiculously fast!
Jarrett (verified owner) –
Fast fast fast shipping!! Plates are just as described.
Gary L. (verified owner) –
Great plate. Solid and lightweight. Would buy again.
Matthew C. (verified owner) –
Love these plates, they work great with my Crye JPC 2.0. Fit and look great!!
Tyler Y. (verified owner) –
For those of you on the fence about this. And AR500 branded armor. RMA is and always will be. The winner. Every time. Very timely with the whole process. Ordered Friday. Shipped Monday for a product in stock. Can I say anymore? If you want a quality. USA made product. Just do it.
Robert (verified owner) –
Hopefully never test these to give an actual review but RMA has my respect. Got my plates in 2 weeks despite the 6-8 week lead time so I havent even gotten my carrier yet. The price and weight of this plate (1091) make it available to anyone. After tons of research, there wasnt really another contender for my price range which was about 500.
Steven W. (verified owner) –
This was my second set of armor, I originally bought the SRT plates which were super light. I have those in a Ferris Concepts carrier and it was a great fit. I bought these plates because I wanted a higher threat level plate. I found both of these plates were packaged really well, and they looked superb coming out of the box. I went with RMA because it’s an American company, and he’s a former Marine like myself. I also found their site easier to navigate than all other companies, and their pricing was really good. I wouldn’t hesitate to buy from them. I’m still waiting until the 26th of this month to get my JPC plate carrier, which are now sold at RMA. I also bought this plate because it was multi curved. Overall these plates are a great buy.
Austin C. (verified owner) –
Really quick shipping and high-quality product. I would strongly recommend.
Anonymous (verified owner) –
Should work fine.
NW (verified owner) –
NIJ tested plates that give you the protection that most need, yet comfortable to wear for extended times, and are at a competitive price point.
My 1093’s are in rotation with my 1155’s. Thank you to the staff at RMA for the recent fast shipment of the 1091’s (wife).
Ordered 1/14/2021 received 2/5/2021
Peter (verified owner) –
Fit is good, for a range officer –
Jake P. (verified owner) –
Great light weight armor, I’ve worn this in my fully loaded carrier for 12+ hours straight with minimal discomfort. Highly recommend.
Richard M. (verified owner) –
100 times better than the Steel plates these replaced
Lighter better fit and ceramic versus steal.
And affordable what’s not to like?
Albert B. (verified owner) –
Lightweight and they fit perfectly into the shell back. I use them when working out.
MICHAEL (verified owner) –
Best bang for the buck multi curve plates. They work well in my LV119.
Anonymous (verified owner) –
By far the Best plates for the price! Nij .07 tested
Joseph (verified owner) –
Quality American made product. I would not trust my life to the many Chinese made knockoffs out there now. Go with American made RMA. It’s good stuff. Bought the Iii+ and although the wait time was a while based on demand, it was worth it.
Bryan (verified owner) –
Excellent balance of protection with moderate weight. The plate is on the lighter side of the weight spectrum but still offers solid rifle protection. It is a great value and a good buy at the price. It is one of the better rifle plates available on the market today.
Scott (verified owner) –
Exceptionally well made; exceptionally light. The multi-curve and padding make these plates very comfortable – they can be worn for extended periods without fatigue.
They fit a medium LBT 6094 very well. Nearly unnoticeable weight addition to a carrier – you’ll be surprised when you pick it up.
Josh (verified owner) –
Hands down the best armor out there. Amazing quality. Shipped exactly when the lead time was up and the multi curve feels great and it’s not bad at all weight wise. Highly recommend RMA to anyone.
Patrick (verified owner) –
Lightweight and comfortable, the plates arrived within the time frame listed on the website. Very glad I went with these over steel. I am 6’2″ but have a long torso, the lg sapi fit better than 11×4 steel armor and are about half the weight. Would reccomend to anyone looking for 3+ protection that doesnt want 15 to 20lbs in their rig. Fit my lg Shellback Tactical SF perfectly.
Cameron (verified owner) –
Great Product and Great Service!
Anonymous (verified owner) –
Awesome plates at an incredible price. They fit well in my JPC 2.0.
Neal (verified owner) –
Way awesome plates! Super comfy!
Anonymous (verified owner) –
A bit of a tight fit in the Warrior LPC but works great
nobabymomadrama (verified owner) –
Excellent extra large plates in 3+ rating what more could I ask for, they are a bit thick though so they barely fit in my Shellback SF carrier but I managed so Oh well at least they are light!!! 🙂
Shahzeb (verified owner) –
These are the absolute best plates for the money! Light, multicurve, 3+ protection against most common threats in CONUS. There is a lead time however, RMA shipped it within the time frame packaged perfectly. Highly recommend
Anonymous (verified owner) –
Arrived as described and fit well in a Ferro Slickster. Lightweight and comfortable
Kenneth (verified owner) –
Wow, these are light and amazing plates. Looking to get another pair soon for the wify
Anonymous (verified owner) –
Super comfy
Maxwell (verified owner) –
Durable, light and great warranty. Fits as intended
Christopher Pike (verified owner) –
Fits my plates carrier like a glove. Looks like it was made well. Haven’t been shot yet but if it happens I will let you know how they work😂
Andrew J. (verified owner) –
Amazing product at an amazing cost. Would buy again, but hopefully I don’t need to.
Chloe R. (verified owner) –
Absolutely amazing! Lightweight and good quality. These work really well for me as a woman, although I am looking forward to the female specific armor y’all have coming.
Evan B. (verified owner) –
Best deal going right now. Light, comfortable. A little thick but fits in the Slickster. Looking to order another set.
Rob K. (verified owner) –
Extremely light and fit snugly in a JPC.
James (verified owner) –
Fits small-size Crye JPC2.0 perfect. Tight, but fits neatly once shimmied in. Super comfy, curved is advisable. Very happy with the product overall. Hope they work if I ever need them for more than a workout!
Anonymous (verified owner) –
Great plates that are a good balance of lightweight and affordable. They fit nicely in a JPC 2.0 even though they are little on the thick side.
Anonymous (verified owner) –
Solid. Hope I don’t end up actually using it to stop bullets, but it seems like it would do the trick.
Steven Miller (verified owner) –
Having purchased two of these plates, a front and rear I believe the value for the money to be excellent. The lead time for delivery was clearly stated on the website and RMA Armament was right on schedule.
Ryan S. (verified owner) –
These plates are awesome, really comfortable, and light weight. They fit into my carrier perfect. Best plates for the money.
TYLER (verified owner) –
Upgraded my plates from Hesco 4401’s to these RMA 1092’s and am so happy I made the switch. These plates are close to half the weight of my Hesco’s and the multi-curve is so much more comfortable than single curve.
These plates are a little on the thick side at 1.2″, but I honestly don’t notice the extra thickness. They’re snug in my Spiritus LV119 Covert but still slid in fairly easily. Great plates, great company. 100% recommend for anyone wanting to shed some poundage off their setup.
Greg (verified owner) –
Great product, light, and professionally made.
Henry (verified owner) –
These are awesome plates! The multi-curve and foam padding is super comfortable and the plates are pretty light. One thing to be aware of, though, these plates are thick. I bought the Large size and mine measure 1.2” (like the description says) but between the thickness and the multi-curve, it was a tight squeeze in my PC. They did fit, it just took some effort to get them in. RMA was also quick to answer my questions! Overall very happy with the plates and company!
Kristina W. (verified owner) –
I got a little impatient, but got the product in a reasonable time. Cory does a great job fielding questions. Will refer friends to RMA.
Anonymous (verified owner) –
Came as described. Best plates for the money.
Joe S. (verified owner) –
very comfortable fit and the weight of the plates isn’t bad either. The plates are great so far.
Anonymous (verified owner) –
Very light and seem well made. M plates fit perfectly in my M Crye JPC 2.0
Sean C. (verified owner) –
The curve and size small fit me very well with having a 5’7 165lb frame. The weight makes it excellent for movement and doesn’t weigh on your shoulders like plates made of other materials. If you’re looking for quality III+ plates at a good price RMA is the way to go.
James P. (verified owner) –
Fits perfect and comfortable. Extremely light weight. And very reasonable price.
David F. (verified owner) –
Light weight, good price, and received it quickly!
aaron k. (verified owner) –
The plates is very comfortable. It’s pretty tight in my crye jpc 2.0, but it fits, I’m very pleased with it. I will buy more of them.
David F. (verified owner) –
Great price and light weight for the amount of protection the armor provides!
derek_r –
I just received my 1092 plates today and they are incredible. Extremely light and has nice padding/cushion surrounding the entire plate. They are very comfortable and the curves on the plate hug the body much better than my Highcom plates do and the Hesco plates I have tried. The specs are true to the plate. 1.2″ thick and 4.49lbs. Spoke several times with Blake the owner and he is extremely transparent and friendly. I highly recommend this plate to anyone looking for a low cost low weight plate. The only downside is the are on the thicker side but a work of art non the less. Thank you guys very much. I am extremely pleased with these plates. All American made materials. RMA doesn’t source material overseas like some other brands.